Welcome to Cheerico Macaron Stand!

8 Tier Acrylic Square Maypole Cupcake Stand Display


Be the first to review this product

Availability: In stock


Quick Overview

This 8 Tier Square Maypole Cupcake Stand can be used as 8 tier or smaller tier. It is specially designed so it can be used as smaller cupcake stand. All tier can be used as top tier or bottom tier.

The entire size: 
Length 19.7" Width 19.7" Height 28.7"
Length 500 * Width 500 * Height 728mm

This stand will hold around 162 cupcakes.

8 Tier Acrylic Square Maypole Cupcake Stand Display

Double click on above image to view full picture

Zoom Out
Zoom In

More Views

Product Description

8 Tier Square Pole Cupcake Stand 

Length 19.7" Width 19.7" Height 28.7"

Length 500 * Width 500 * Height 728mm 

Tier1: Dia 150mm, (5.9")
Tier2: Dia 200mm, (7.9")
Tier3: Dia 250mm, (9.8")
Tier4: Dia 300mm, (11.8")
Tier5: Dia 350mm, (13.8")
Tier6: Dia 400mm, (15.7")
Tier7: Dia 450mm, (17.7")
Tier8: Dia 500mm. (19.7")

# 1st,2nd,3rd,4th,5th,6th,7th tier is 4mm (0.16") thick, 8th tier is 5mm (0.2") thick 

#Rod Pillar Size : Diameter 40mm x 100mm Height 
# 1st,2nd,3rd,4th,5th,6th tier is 4mm thick, 8th tier is 5mm thick 

Flat packed in cardboard carton, each component is protected with bubble wrap.

# 1st,2nd,3rd,4th,5th,6th,7th tier is 4mm thick, 8th tier is 5mm thick 
# The total height of the stand is 728mm. 
# The acrylic comes wrapped in the manufactures protective covering

There is no need for glue or other fixings.
The edges of the acrylic are perfectly clear and polished.
Every part of the stand has been accurately cut and finished
Can be taken apart, washed and stored away for another time.
The stand comes flat packed and only takes a few minutes to assemble.

How many cakes can it hold? Refer to the diagram below for the rough reference

We base our numbers on using a 50mm diameter cupcake for our Square range.


Assembly Instructions: very simple and quick to assemble. Simply fasten each screw to the corresponding rod, there is no need for glue or other fixings/hardware. View this instructional video on how to put the Maypole Cupcake Stand together.;The four small round plastic feet are included, and you can mix the plates as any plate can be used as top or bottom tier.

PLEASE NOTE: You must remove the manufacturers’ protective cover before assembling this product. This covering is clear bubble and cling wrap on both sides of every acrylic component.

Download Assembly instructions for Square Maypole cupcake Stand


Parts: Acrylic discs, head screws, double screws, acrylic rods and acrylic feet.

* Remove the manufacturer’s protective cover from BOTH side of each acrylic component.
* Begin by placing the feet to the underside of the bottom disc ensuring they are evenly spaced.
* Take a metal head screw and place it on to a flat surface where the stand is to be constructed
* Carefully line up the hole(s) of the largest disk with head screw ensuring the disc is resting securely on the acrylic feet.
* Now screw the first rod onto the screw thread of the head screw making sure the acrylic disc is clamped firmly between two components.
* Continue by placing the next largest disc on to the screw thread of rod and tighten each piece as you go.
* The final rod is to be used as the supposed for the top tier and the stand is completed by adding the other screw cap into the top.


* The stand is made from acrylic which will scratch if it is not looked after properly. 
* To clean the product use warm water with a little washing-up liquid and soft cloth. 
* Do not use any abrasive cleaning products as they will make the acrylic. 
* Do not put the stand in a dishwater

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.